Windows Server 2008 Event Id 1054
There are unknown LdapIpAddress entries. Great for personal to-do lists, project milestones, team priorities and launch plans. - Combine task lists, docs, spreadsheets, and chat in one - View and edit from mobile/offline - Cut down thx 0 Comment Question by:mcrmg Facebook Twitter LinkedIn https://www.experts-exchange.com/questions/28243055/event-id-1054-The-processing-of-Group-Policy-failed.htmlcopy LVL 12 Best Solution bypiattnd One thing you can try is disable all non Microsoft services and run it for a bit Active Directory-integrated domain name is not displayed in DNS snap-in with Event ID 4000 and 4013 messages (http://support.microsoft.com/kb/316685) Note: This article was inspired by the Directory Services forum thread DNS Stop http://getbetabox.com/event-id/event-id-1054-group-policy-windows-2008.html
Leave a Reply Cancel replyYou must be logged in to post a comment. Error code 1355 (The specified domain either does not exist or could not be contacted) Use Networking troubleshooting procedures to further diagnose the problem (http://go.microsoft.com/fwlink/?LinkId=92706). Type _ldap._tcp.dc._msdcs.domain.com and then press ENTER. Verify your Domain Name System (DNS) is configured and working correctly.
Event Id 1054 Group Policy Windows 2008 R2
GPResult shows GPOs being applied. Event Id 1054 Cannot Obtain The Domain Controller Name Make sure there is only one IP address for each DC. x 7 Private comment: Subscribers only. https://support.microsoft.com/en-us/kb/324174 Verify your Domain Name System (DNS) is configured and working correctly.Event InformationAccording to Microsoft :Cause :This event is logged when the processing of Group Policy failed and Windows could not obtain
Events appearing in the event log may not reflect the most current state of Group Policy. Event Id 1054 Windows 2012 If not, it falls under the multihomed DC issue in #2. 6. When the gpupdate command completes, open the Event Viewer. Group Policy Infrastructure Group Policy Group Policy Preprocessing (Security) Group Policy Preprocessing (Security) Event ID 1054 Event ID 1054 Event ID 1054 Event ID 1052 Event ID 1053 Event ID 1054
Event Id 1054 Cannot Obtain The Domain Controller Name
Events appearing in the event log may not reflect the most current state of Group Policy. Resolution 4: Disabling spanning tree on the switches (Cisco Catalyst) Note: STP=Spanning Tree Protocol. Event Id 1054 Group Policy Windows 2008 R2 To diagnose the failure, review the event log or run GPRESULT /H GPReport.html from the command line to access informati on about Group Policy results. Event Id 1054 Error Code 58 Regards, Andy Marked as answer by Andy QiMicrosoft contingent staff, Moderator Monday, October 29, 2012 6:43 AM Sunday, October 21, 2012 1:18 PM Reply | Quote Moderator 0 Sign in to
All goes well for a very long time. http://getbetabox.com/event-id/event-id-7038-windows-server-2008-r2.html Comments: EventID.Net According to Microsoft, this event occurs because the domain from which the group policy should be downloaed either does not exist or could not be contacted. This is the "same as parent" name under the zone. Examples of NICs known to exhibit this issue:- Broadcom Gigabit Adapter- Intel Gigabit Ethernet PRO Adapter, Intel Pro/1000- Intel 82544EI-based XT Gigabit Adapter (82540EM chipse)- Compaq/HP NIC dual interface 10/100/1000 doing Event Id 1054 Group Policy Windows 7
Edited by Mark Hasd Friday, October 19, 2012 6:04 PM Friday, October 19, 2012 6:03 PM Reply | Quote Answers 0 Sign in to vote Hi, Regarding the current issue, I Click Start, point to Settings, and then click "Network and Dial-up Connection". On the client computer, run ipconfig /flushdns and check again. http://getbetabox.com/event-id/event-id-in-windows-server-2008.html User policy could not be updated successfully.
A reboot fixes it for a while but then it drifts and EventID 1054 resume. Windows Could Not Obtain The Name Of A Domain Controller If you have not yet done any DNS troubleshooting, then Ensurethat the DNS server service is running on the computer providing DNS services and logging this error. If they do not, then we need to look at your SRV records as well as whether any of the above summarized causes are contributing to the non-DC responses, such as
This could be caused by a name resolution failure.
Reboot the server and observe over the next week or 2 to see if the problem comes up again. 0 Message Author Comment by:mcrmg ID: 395031942013-09-18 okay, will try that http://www.microsoft.com/technet/support/ee/transform.aspx?ProdName=Windows+Operating+System&ProdVer=5.2&EvtID=1054&EvtSrc=Userenv&LCID=1033 0 LVL 2 Overall: Level 2 Message Expert Comment by:pjwallis ID: 395031272013-09-18 Hi, Could you have a look at the following and see if it fits your needs? Incorrect permissions or security failures can prevent Group Policy from applying to the computer or user. Windows Could Not Obtain The Name Of A Domain Controller Server 2012 Yes No Additional feedback? 1500 characters remaining Submit Skip this Thank you!
Make sure time is configured properly. Does the error detail "The Specified server cannot perform the requestion operation." suggest that the issue isn't actually finding a DC, but something else failing? See the following link for more information. navigate here From previous reports, Microsoft supposedly fixed it in Windows 2003 SP2, but something may have changed in recent AMD core releases causing it again.
Windows could not obtain the name of a domain controller. I'd also go to the startup tab and disable all items that are not critical to system operation. Join Now For immediate help use Live now! The following errors were encountered: The processing of Group Policy failed.
In the command prompt window, type gpupdate and then press ENTER. It was found the AMD Opeteron processor has timing issue. Custom search for *****: Google - Bing - Microsoft - Yahoo Feedback: Send comments or solutions - Notify me when updated Printer friendly Subscribe Subscribe to EventID.Net now!Already a subscriber? Windows could not obtain the name of a domain controller.
You’ll be auto redirected in 1 second. See Start, stop, pause, or restart a DNS server for steps on how to accomplish that task. Using a DNS address that doesn't have the AD zone data. On the client computer, run ipconfig /flushdns and check again.